Huayu "2 in 1" microinverter HY-800-Plus, compatible with 400-670Wp solar panels, is designed for dual-module applications with parallel DC input, module-level MPPT and module-level monitoring for individual solar panels, other than built in rapid shutdown, its AC cables integrated and optional built in Wi-Fi data logger greatly lower LCOE of solar installation during 25 years of standard warranty.
Overview
Huayu "2 in 1" microinverter HY-800-Plus, compatible with 400-670Wp solar panels, is designed for dual-module applications with parallel DC input, module-level MPPT and module-level monitoring for individual solar panels, other than built in rapid shutdown, its AC cables integrated and optional built in Wi-Fi data logger greatly lower LCOE of solar installation during 25 years of standard warranty.
Features
Safer
The max. DC input voltage is only 60Vdc(built-in Rapid Shutdown) which gets rid of risks caused by electric shock and ark fault and is absolute safe for installers and solar system owners.
Smarter
Every specific module is monitored by "Huayu Portal Monitoring Platform" which is accessible on both webpage and by "Huayu Portal" Apps at smart devices.
More Powerful
Startup voltage is as low as 20Vdc which lengthen power generation time and modular parallel connection to grid and module-level MPPT avoid the impact of shading and mismatch of solar panels.
More Reliable
IP67 waterproof enclosure rating and protection glue injected for PCBAs extend the lifespan of microinverters installed in outdoor harsh conditions.
More Cost Effective
3m+ AC cables integrated and optional built in Wi-Fi data logger greatly lower LCOE of solar installation during 25 years of standard warranty.
| Data Sheet | HY-800-Plus | ||
| Input Data(DC) | |||
| Commonly Used Module Pairings | 2×400W~600W | ||
| Maximum Input DC Voltage | 60V | ||
| Power Point Tracking Voltage Range | 22~55V | ||
| Operating Range | 16~60V | ||
| Startup Voltage | 20V | ||
| Overvoltage Class DC Port | II | ||
| DC Port Backfeed Current | 0 A | ||
| PV Array Configuration | 1 x 1 ungrounded array; No additional DC side protection required; AC side protection requires max 25A per branch circuit | ||
| Max.Input Current | 2×17A | ||
| Output Data(AC) | |||
| Peak Output Power | 880W | ||
| Maximum Continuous Output Power | 800W | ||
| Nominal (L-L) Voltage/Range | 240/211~264V | 208/183~229V | 230/Configurable |
| Maximum Continuous Output Current | 3.2A | 3.36A | 3.26A |
| Nominal Frequencyy/Range | 60Hz/59.3~60.5Hz | 50Hz/Configurable | |
| Extended Frequency/Range | 45~55Hz / 55~65Hz | ||
| AC Short Circuit Fault Current Over 3 Cycles | 15Arms | ||
| Maximum Units Per 20 A (L-L) Branch Circuit | 5 | 5 | 5 |
| Overvoltage Class AC Port | III | ||
| Power Factor(Adjustable) | >0.99 Default, 0.8 Leading... 0.8 Lagging... | ||
| Level of Harmonics Distortion | <3% | ||
| Efficiency | |||
| CEC Weighted Efficiency | 95% | ||
| Peak Inverter Efficiency | 96.50% | ||
| Static MPPT Efficiency | 99% | ||
| Night Time Power Consumption | ＜50mW | ||
| Mechanical Data | |||
| Ambient Temperature Range | -40ºC~+65ºC | ||
| Relative Humidity Range | 4% to 100% (condensing) | ||
| Connector type: DC | MC4 | ||
| Dimensions(W*H*D) | 268×250×42 mm（Without mounting bracket and cable） | ||
| Weight | 2.9kg | ||
| Cooling | Natural Convection-No Fans | ||
| Approved for Wet Locations | Yes | ||
| Pollution Degree | PD3 | ||
| Enclosure Environmental Rating | IP67 | ||
| AC Cable Length(Integrated with AC Connectors) | 3m+ | ||
| Features | |||
| Communication | PLC(Extra Data Logger) / Wi-Fi(Data Logger Built-in) | ||
| Monitoring | Support remote web page monitoring and local MDL monitoring | ||
| Disconnecting Means | The AC and DC connectors have been evaluated and approved by UL for use as the load-break disconnect required by NEC 690 | ||
| Compliance | UL1741, INMETRO,VDE4105, VDE0126, IEC62109, EN50549, CE & INMETRO etc. | ||
| Warranty | 25 years | ||
